If you’ve ever stood in a feed mill control room at 2 a.m., staring at a scale that’s off by 0.2 kg, you know how one tiny mix-up with feed additives can spiral into real problems—for your team, for the animals relying on your feed, and for your bottom line. I’ve been in this industry for 12 years, starting as a lab tech testing premixes before moving into sales, and I’ve seen every mistake imaginable: a customer forgot to calibrate their micro-ingredient feeder, a mill blended a probiotic with a too-short retention time, a swine nutritionist dosed a phytase at half the recommended rate because they mixed it with a coarse ingredient first that separated it mid-blend. Most of these errors weren’t from bad intent—they were from skipping the small, specific steps that turn “adding additives to feed” into a process that’s actually correct. As a feed additives supplier, I don’t just sell you enzymes, probiotics, amino acids, or mycotoxin binders—I walk you through how to use them right, because that’s where their value lives. Let’s break down the correct way to mix feed additives, from pre-blend prep to post-mix testing, with real-world lessons I’ve learned from working with poultry, swine, and aquaculture operations across the Midwest. Feed Additives

First, let’s talk about the foundation: knowing exactly what you’re working with before you even touch a scale. This might sound obvious, but I can’t tell you how many times a customer has called me panicking because they ordered a 10% lysine premix but grabbed a 50% one by mistake, or mixed a heat-sensitive B-vitamin with a mineral that’s abrasive enough to destroy 30% of its activity. Step one here is to verify every single ingredient’s specs against your formulation sheet—no exceptions. If you’re using a phytase, check the activity unit (FTU) on the CoA (certificate of analysis) I send you; don’t just go by the “grams per ton” number, because different suppliers have different definitions of a gram. Last year, a broiler operation I work with thought they were using 500 FTU/kg of phytase, but their CoA said the product was actually 1,200 FTU/g—they’d mixed up grams and kilograms, so they were overdosing and wasting money. That’s the kind of avoidable mistake that kills trust, and it starts with pre-mix verification. Also, check the physical properties of your additives: are they fine particles or coarse? Are they hydrophobic (water-repellent) or hygroscopic (absorbs moisture)? If you’re mixing a hydrophobic probiotic with a wet feed mash, it will clump and never distribute evenly—something I always note in my product data sheets, but not every customer reads closely.
Next, the order of mixing is non-negotiable, and it’s a step most people get wrong. Let me explain: micro-ingredients (additives that make up less than 1% of the total feed, like enzymes, mycotoxin binders, and trace minerals) should never be added directly to the main batch. They’re too potent, and their fine particles separate easily from coarser feed ingredients during blending. The correct sequence is called a “pre-blend” or “piggy-back blend,” and here’s how to do it: start with your carrier. A carrier is a dry, inert ingredient that matches the particle size of your micro-additive, so it acts as a buffer to spread the additive out. For fine micro-additives, use a carrier like ground corn middlings or rice hulls—something with a similar particle size, not fine sand, which is too dense and will sink to the bottom. For example, if you’re mixing 1 kg of a 10% phytase premix into a 1,000 kg batch of feed, first take 10 kg of ground corn middlings (10x the volume of the premix, minimum) and put it in a small mixer. Add the phytase premix to the carrier, run the mixer for 3-5 minutes on low speed, then check for uniformity: take a small sample, rub it between your fingers—there should be no fine “dust” left, just an even, light tan color (matching the phytase’s natural color). If you see clumps, run it a minute longer. Once your pre-blend is uniform, add it to the main mixer with the coarse ingredients (like corn, soybean meal, wheat) that make up 70-80% of the total feed, not the small ingredients like salt or calcium carbonate. If you add pre-blends with salt, which is coarse, you’ll end up with pockets of high and low additive concentration as the mixer runs. I always tell customers: “add the potent stuff first to the big, bulky stuff, not the other way around.” Another rule here is to never mix heat-sensitive additives (probiotics, B-vitamins, some enzymes) at the same time as steam-pelleting conditioning, which runs at 160-180°F. If you need to pellet, add the heat-sensitive additives post-pelleting, either through a liquid spray or a dust-on applicator that coats the pellets evenly, rather than mixing them into the mash.
Now, blending equipment: not all mixers are created equal, and using the wrong one for additives is a fast way to get bad results. There are two main types of mixers used in feed mills: ribbon blenders and twin-shell (V-blenders) blenders. Ribbon blenders are common in large, industrial mills, but they can cause more particle separation if the blade speed isn’t set right. Twin-shell blenders are better for small, micro-ingredients because they tumble materials evenly without shearing them apart. Here’s the mistake I see: a customer uses a twin-shell blender set to run for 2 minutes for all batches, regardless of size. That’s too short for micro-additive pre-blends. For a pre-blend of 100 kg, you need to run the twin-shell blender for 5-7 minutes at 18-22 RPM (check your mixer’s manual for specs)—that’s the sweet spot where particles mix without bouncing apart. Another big issue is loading order: if you load the heavy, dense ingredients (like calcium carbonate) first, then add your light pre-blend on top, the light particles will ride on top of the dense ones and never mix. Load your pre-blend with the medium-density ingredients, and always follow the mixer manufacturer’s loading sequence, which I also include in the technical data for each of my additives. For small-scale operations (like a farm that mixes its own feed for 500 hogs), a 5-cubic-foot ribbon blender works, but you have to batch smaller volumes—never fill it more than 2/3 full, because overloading kills mixing uniformity. I once worked with a family-owned hog farm that filled their blender to the brim to save time, and they ended up with 20% of their feed having zero added amino acids, leading to stunted pig growth. Don’t cut corners on mixer loading and speed.
Calibration is the unsung hero of correct mixing, and it’s something that should happen at the start of every shift, not just when a scale is “broken.” Micro-ingredients are dosed in grams per ton or parts per million, so even a 5% error in scale calibration means under or over-dosing by 5%—a small number that adds up to thousands of dollars in wasted additives, or reduced animal performance. How to calibrate correctly, per standards set by the Association of American Feed Control Officials (AAFCO), which I follow for all my product specs: first, make sure the scale is on a level surface, no objects leaning against it, and the power cord is secured (vibration from mill equipment can throw scales off). Next, test the scale’s accuracy with traceable calibration weights—most mills have 1 kg and 5 kg weights, but I recommend doing a full range test: weigh a 10 kg, 50 kg, and 100 kg load, and adjust the scale’s calibration setting if it’s off by more than 0.2% (that’s the acceptable error for feed additives). For micro-ingredient feeders (the ones that dispense premixes), calibration is even more frequent: test them every 4 hours during a shift, or every time you change an additive lot. For example, if your premix feeder is set to dispense 100 g of phytase premix, run 10 test cycles, weigh the total amount, and divide by 10—you should get 100 g per cycle within 1 g of error. Last year, a poultry mill I supply had a micro-ingredient feeder that was dispensing 15% less amino acid than it was set to, because the feeder’s worm gear wore out; they didn’t calibrate for 6 months, and their broilers had 10% lower feed conversion ratio (FCR) because of the under-dosed amino acid. That cost them an estimated $120,000 in lost revenue—all because of skipping a 10-minute calibration check.
Then there’s post-mix testing, which is the only way to confirm your mixing was correct, not just guessing. Too many mills skip this step, assuming that if they followed the steps, it’s right. But uniformity testing is simple, cheap, and can catch mistakes before feed goes out to animals. The standard for feed additives is to test for coefficient of variation (CV), which measures how evenly the additive is distributed across the batch. A CV of less than 10% is considered acceptable for most micro-additives, per AAFCO. Here’s how to do it: take 10 random samples from different parts of the mixer (top, bottom, left, right, center) after mixing is done, each sample weighing 1 kg. Test each sample for the additive you used—for example, if you added a vitamin premix, test for vitamin D3. If the CV is higher than 10%, that means your mixing time was too short, your pre-blend was not uniform, or your scale was off. Last month, I worked with an aquaculture feed producer who mixed a mycotoxin binder for shrimp feed; they skipped post-mix testing, and 15% of the feed had no binder, leading to a 25% higher mortality rate in the shrimp. Testing for uniformity would have caught that, and it takes less than an hour with a lab test kit I can provide for most of my additives, at no extra cost. I always encourage customers to run these tests, even if it’s just once a week, to catch small issues before they become big problems.
Wait, I should also talk about common mistakes specific to different types of additives, because enzymes are mixed differently than probiotics, which are different than mycotoxin binders. For example, mycotoxin binders are usually coarse, so they don’t need a pre-blend, but they should be added late in the mixing sequence, because if you add them with the coarse ingredients, they can coat those ingredients and prevent other additives from mixing evenly. Probiotics, as I mentioned earlier, are heat and moisture-sensitive, so they should only be mixed in cool, dry mash, and never with water-based liquids unless you’re using a coating agent to protect them. Enzymes (like phytase, amylase) are usually stable, but they’re fine, so they need a pre-blend with a matching carrier to avoid separation during pelleting. I include these specific mixing notes for every product I sell, but I know how easy it is to toss the data sheet in a drawer, so I always follow up with a quick call a week after delivery to walk through any questions.
Another point: documentation. It might seem tedious, but keeping a log of every mixing step—what additive lot you used, the scale calibration results, mixing time, post-mix CV test results—means you can trace a problem back to its source if something goes wrong. For example, if a customer has a batch of feed with low amino acid levels, the log will show if the scale was calibrated that day, what feeder was used, and if the pre-blend test passed. I always share a free digital log template with my regular customers, so they don’t have to build one from scratch. It’s a small tool, but it prevents a lot of finger-pointing when issues come up.
Let’s circle back to the reason this matters: it’s not just about following rules, it’s about animal health and performance. When you mix feed additives correctly, you get the full value of the product I sell you—no wasted money on overdosed additives, no lost revenue from under-dosed ones, no animal health issues from uneven distribution. I’ve seen customers cut corners on mixing to save time, and it almost always backfires. The operations that work with me, follow these steps, and take the time to do it right are the ones that have consistent FCR, lower mortality, and higher profit margins.

If you’re struggling with mixing additives, or you’re looking for a reliable supplier that will walk you through these steps, I’m here to help. I don’t just ship products— I provide the support to make sure they work as intended, because that’s what a true partner in feed additives does. Feel free to reach out to discuss your specific mixing challenges or to learn more about our product line.
Thickening Agent References
- Association of American Feed Control Officials (AAFCO). 2023. Official Publication. AAFCO, Oxford, IN.
- Swatland, H. J. 2008. Mixing uniformity in animal feeds: A review. Journal of Applied Poultry Research, 17(1):146-155.
- Zhang, Y., et al. 2021. Factors affecting mixing uniformity of micro-ingredients in feed premixes. Animal Feed Science and Technology, 276:114982.
- National Research Council (NRC). 2012. Nutrient Requirements of Swine, 11th ed. National Academies Press, Washington, DC.
Qingdao Longfeng Chemical Co., Ltd.
With abundant experience, we are one of the most professional feed additives manufacturers and suppliers in China. We warmly welcome you to buy bulk premium feed additives at competitive price from our factory. If you have any enquiry about free sample, please feel free to email us.
Address: B612, NORD PLAZA, NO.328 DUNHUA ROAD, QINGDAO, SHANDONG, CHINA
E-mail: Tony@longfengworld.com
WebSite: https://www.longfeng-chem.com/